鉅坤科技股份有限公司

規格與說明

Radio Gateway Series

 無線電閘道器

硬體規格 :

可整合無線電Radio介面卡/FXS/FXO/T1/E1

本主機需搭配CPU控制卡:

• CPU：ATOM N2930
• 記憶體：DDRII 4GB
• 網路端 口：10/100/1000 LAN ,
• 硬碟容 量：120G 
• USB 2.0 Port：2 (Front)
• 工作溫度：0 - 40°C
• 工作溼度：8% to 90% (non-condensing)

語音規格

• 符合SIP RFC 3261 / H.323 規範(ITU-T) 通信協定
• 語音壓縮規格: G.711,G.722,G.723,G.726,G.729,GSM,Slin,Lpc10,Speex

自動總機

• Web 介面自動總機語音流程編輯
• 特定時間宣告語
• 假日工作時間設定
• 支援多國語言

交換機ISDN鍵結

• Toshiba,NEC,Alcatel,Avaya,phillips...等

語音郵箱

• 支援多國語言
• SIP留言指示
• 電子郵件通知
• 可由Web存取語音留言
• 可由電話聽取語音留言

會議功能

• 隨取建立會議室
• 個人虛擬會議室
• 會議事件提示音
• 單一會議室最多可容納32名成員
• 可由網路電話登入

加強功能

• 多應用IVR(語音互動系統) 資料庫
• 可支援SIP/H323/MGCP/G-Talk/OCS/Skype 鍵結

精選電話功能

• 通話轉接Transfer
• 來電轉送Forward
• 來電轉送通知Forwarded Notice
• 撥號限制Call Screening
• 去電顯號設定Caller ID Privacy
• 來電等候Call Waiting
• 通話保留Call Hold
• 來電代接Call Pickup (Global, Group)
• 指定代接Specified Call Pickup
• 電話跟隨Follow Me
• 勿打擾Do Not Disturb
• 去電顯示替換ANI Replacement
• 回撥Call Return
• 隱藏或顯示主叫號碼Hide /Show ANI Selection
• 通話駐留與取回Call Park/Retrieve
• 分機註冊Extension mobility

●忙線自動回覆 busy call

規格與說明

T-288C/NC  Leased Line Modem

SPECIFICATIONS

Compatibility

V.34+ 33.6/31.2Kbps 4DTCM

V.34 28.8/26.4/24/21.6/19.2/16.8/14.4/ 12/9.6/7.2/

4.8/2.4Kbps 4DTCM

V.33 14400/12000/9600/7200bps TCM, 4800bps QAM

V.32bis 14400/12000/7200bps TCM

V.32 9600bps TCM, 9600/4800bps QAM

V.29 9600/7200bps QAM, 4800bps DPSK

V.27bis 4800/2400bps DPSK

V.26 2400/1200bps DPSK

V.22bis 2400bps QAM

V.22/Bell 212A 1200bps DPSK

V.23 1200/75, 600/75bps FSK

V.21/Bell 103 300bps FSK

Data Format

Synchronous or Asynchronous

Total bit length: 8, 9, 10, 11

Data Speed

Asynchronous

75/300/600/1200/2400/4800/7200/9600/12000/

14400/16800/19200/21600/24000/26400/28800/

31200/33600/38400/57600/76800/115200bps

Synchronous

1200/2400/4800/7200/9600/12000/14400/16800/

19200/21600/24000/26400/28800/31200/33600bps

DTE Interface

EIA RS-232C, ITU-T V.24/V.28

Line Requirement

Dial line, 2/4 wire leased line

Transmit Level

Dial line: 0 to -15dBm for where allowed, or fixed -10dBm

Leased line: -6 to -31dBm for V.34

0 to -31dBm for other V-series

Receive Dynamic Range

+3 to -26, +3 to -40, -6 to -33, -6 to -43dBm

Equalization

Automatic adaptive EQ

Compromise EQ: M1040 or cable

Call Progress Monitoring

Dial tone, Ring, Ringback, Busy and Backup dial

Line Status Monitoring

TX level, RX level, S/N ratio, Delay, Freq. offset, Far-end

echo freq. offset, Near-end echo, Far-end echo, Retrain

count, Tx Baud Rate, Rx Baud Rate, Tx Carrier, Rx Carrier,

Tx Power Back-off level

Memory

A nonvolatile memory for storing 10 sets of user profile and

10 telephone numbers with 20 characters, the 10 sets of

factory default are stored in ROM

Line Interface

RJ-11 for Dial Line, JM8 for Leased Line

Transmit Clock

Internal, Loopback, External clock

Dialing Command

Extended AT and V.25bis command set

Dialing Type

Tone/Pulse dialing

Flow Control

RTS/CTS, XON/XOFF, CTS only, ENQ/ACK

Power

AC Source: 90 ∼ 265V, Autorange, 47 ∼ 63 Hz

DC Source: -36 ∼ -72V for rack option

Dual redundant power unit for rack option

規格與說明

T-336Cx/Nx/NDx  Leased Line Modem

Specification

Compatibility

• 34+: 33.6/31.2 Kbps SM (4D TCM)
• 34: 28.8/26.4/24/21.6/19.2/16.8/14.4/12/9.6/7.2/4.8/2.4 Kbps SM(4D TCM)
• 32bis: 14400/12000/7200 bps TCM
• 32: 9600 bps TCM, 9600/4800 bps QAM
• 22bis: 2400 bps QAM, 1200 bps BPSK
• 22/Bell 212A: 1200 bps DPSK
• 23: 1200/75, 600/75 bps FSK
• 21/Bell 103: 300 bps FSK

Data Format

• Synchronous or Asynchronous
• Total bit length: 8, 9, 10, 11

Data Speed

• Asynchronous-

75/300/600/1200/2400/4800/7200/12000/14400/16800/19200/21600/
24000/26400/28800/31200/33600/38400/57600/76800/115200 bps

• Synchronous-

1200/2400/4800/7200/9600/12000/14400/16800/19200/21600/
24000/26400/28800/31200/33600 bps

• Total bit length : 8, 9, 10, 11 bits
• Parity bit : odd, even, none
• Stop bit : 1, 1.5, 2 bits

Line Interface

• Cx/Nx: RJ-11 for dial-up, JM8 (like RJ45) for leased line
• NDx: 6-pin Terminal Block or 50-pin Centronic

DTE Interface

• EIA RS-232C, ITU-T V.24/V.28
• Line Requirement
• Dial-up line, 2/4-wire leased line
• Transmit Level
• Dial-up line: 0 to -15 dBm; Leased line: 0 to -31 dBm
• Receive Dynamic Range
• -4 to -43 / 0 to -33 dBm
• Equalization
• Automatic adaptive EQ
• Call Progress Monitoring
• Dial tone, Ring, Ring-back, Busy and backup dial
• Dialing Command and Type
• Extended AT and V.25bis using Tone/Pulse/Mixed
• Clock Source
• Internal/External/Loopback
• Flow Control
• RTS/CTS, XON/XOFF, CTS only
• Diagnostics

Test Features

• 54/V.52 , LAL/DL/RDL
• Test Patterns – 511

Line Status Monitoring

• Tx level, Rx level, S/N ratio, EQM value, delay, phase jitter, freq. offset, far-end freq. offset, far-end echo, DTE format, retrain count, Tx baud rate, Rx baud rate, Tx carrier, Rx carrier, Tx speed, Rx speed, Tx power back-off level, Interface lead monitoring

Power Requirement

• Input
• AC: 90 ~ 265 V, Auto-range, 47 ~ 63 Hz
• DC: -36 ~ -72 V (optional)
• Dual redundant power unit for rack (optional)

Power Consumption

• < 5W

Environment Temperature

• Operating Temperature : 0 °C ~ 50 °C
• Storage Temperature : -25 °C ~ 70 °C

Humidity

• Up to 95% non-condensing

規格與說明

P-MUX Solution Series
EMux-400 (2/4 E1)

Multi-E1 over IP

Evolutionary Convergence in Transmission of real-time Voice/Video and Data over Ethernet Network

Product Overview

EMux-400 is designed as a multi-service access platform for E1 over IP applications. E1 frames can be mapped/de-mapped into/from IP packets. An adaptive clock recovery method for Ingress PDH (PSN -> TDM) clock generation is implemented to support E1 (ITU-T G.823) Jitter performance.

Cost-effective LAN Deployment
(PDH over Ethernet)

EMux-400 provides cost-effective applications of traditional circuit-switched system over IP. With EMux-400, it is easy to interconnect with the existing E1 systems over IP that are used to carry data, voice and video.

Transparent Transmission

EMux-400 can transparently transport proprietary signaling that is required to support PABX & IP-PABX features, including call conference, call forwarding and SS7. Customer can easily apply and enjoy better integration of TDM and Ethernet devices with lower network expense.

Bypass International Toll

With a pair of EMux-400 and guaranteed internet bandwidth, it is sure to save cost dramatically, and to ensure the QoS of voice based on interconnections of TDM telecommunications equipment.

Specification

Line  Interface

Port: up to 4 x E1 (ITU-T G.703)
Interface: RJ-48c (120 Ohm)
Line Coding: HDB3

Ethernet Interface

WAN Port: 100 Base-TX Ethernet

Interface: RJ-45

 LAN port: 100 Bases-TX Ethernet
Interface: RJ-45

Dimension

H x W x D: 44 x 320 x 125(mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                             

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% none condensing

Configuration and Management

RS-232 console port (Craft Terminal) 

規格與說明

IP-MUX Solution Series
EMux-400 (2/4 T1)

Multi-T1 over IP

Evolutionary Convergence in Transmission of real-time Voice/Video and Data over Ethernet Network

Product Overview

EMux-400 is designed as a multi-service access platform for T1 over IP applications. T1 frames can be mapped/de-mapped into/from IP packets. An adaptive clock recovery method for Ingress PDH (PSN -> TDM) clock generation is implemented to support T1 (ITU-T G.824) Jitter performance.

Cost-effective LAN Deployment
(PDH over Ethernet)

EMux-400 provides cost-effective applications of traditional circuit-switched system over IP. With EMux-400, it is easy to interconnect with the existing T1 systems over IP that are used to carry data, voice and video.

Transparent Transmission

EMux-400 can transparently transport proprietary signaling that is required to support PABX & IP-PABX features, including call conference, call forwarding and SS7. Customer can easily apply and enjoy better integration of TDM and Ethernet devices with lower network expense.

Bypass International Toll

With a pair of EMux-400 and guaranteed internet bandwidth, it is sure to save cost dramatically, and to ensure the QoS of voice based on interconnections of TDM telecommunications equipment.

Specification

Line  Interface

Port: up to 4 x T1 (ITU-T G.703)
Interface: RJ-48c (100 Ohm)
Line Coding: B8ZS

Ethernet Interface

WAN Port: 100 Base-TX Ethernet

Interface: RJ-45

LAN port: 100 Bases-TX Ethernet
Interface: RJ-45

Dimension

H x W x D: 44 x 320 x 125(mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                             

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% none condensing

Configuration and Management

RS-232 console port (Craft Terminal) 

規格與說明

Description
IME-910 is an E1 inverse multiplexer enabling the transport of high speed data broadband services over the E1 links. Us-ing G.704 and G.8040 standard to convert Ethernet to multiple E1 by GFP format mapping .IME-910 support 1.984Mbps.
10/100Base-TX or Fiber LAN user interfaces make IME-910 is an ideal solution for high speed broadband application. The inverse aggregation bandwidth is scalable as Nx64kbps [the maximum N=31] with maximum payload bandwidth at 1.984Mbps.
IME-910 can be managed locally by connecting a VT-100 emulated PC to the CID port or remotely through Telnet/SNMP access all on front panel of the unit. Administration, Maintenance, and Provisioning (OAM&P) are provisioned with the use of 16Kbps embedded operation channel (EOC) that runs through the inverse link. Configured with individual IP address for local and remote unit, IME-910 is accessible to the Internet users who are managing the units from a far end place.
To ensure operation continuity and accommodate field requirement, IME-910 offers choices of AC or DC or AC+DC power.

Features
 Connect one high speed broadband over E1 links
 Available in Desktop
 Automatically scale up and down E1 links according to link availability.
 Support data rates N x 64kbps [the maximum N=31] Mbps.
 Use 16Kbps EOC channel for remote configuration and OAM&P.
 Support fiber LAN interfaces
 Comply with ITU-T G.703
 Support VLAN ID Q in Q
 Support dying gasp for remote power failure detection
 Allow a maximum delay of 64 ms among E1 links.
 Support management via VT-100, SNMP

E1 Interface
Standard:
ITU-T G.703, G.704,
No. of E1 output:
1,scaled down automatically per E1 alarms
Line rate:
2048 Kbps +/- 50 PPM
Clock Mode
Internal, Recovery
Line Code:
HDB3
Framing:
PCM31，PCM31C，PCM30 ,PCM30C
Pulse shape:
Meet ITU-T G.703
Impedance:
Balanced 120Ω+/-5% resistive or unbalanced 75Ω+/-5% resistive, software programmable
Connection Type:
RJ-45 or BNC
LAN Interface
Standard:
IEEE 802.3 / IEEE 802.3u
Interface:
IEEE 802.3/802.3u 10/100/1000M Base-T
Data Rate:
N x64K bps[N=1~31]
Bridging Capability:
Complied with IEEE 802.1d transparent bridge
Supports VLAN ID, Q in Q and up to 2048 MAC addresses learning
Connection Type:
RJ45, 4 ports
Ethernet packet size:
Maximum packet size up to 9K jumbo frame
SFP interface
Type
One 100Base-FX 802.3u interface or 1000Base-FX 802.3u interface, SFP type
Alarm and Performance
CID interface:
VT-100/RS-232C/SNMP/Web server
EOC channel:
16Kbps
SNMP:
meet IETF RFC1157,1212 and 2495@10/100Based Tx with RJ-45 connector
Meet G.821 and G.826 for E1 interface
Fiber interface; LOS,
Maintenance
Loopback: LL,RL and NL(local payload loopback)
Power
AC or DC or AC+DC
AC: 90 - 260 V @ 50-60 Hz, 0.2A
DC: -36~ -72 V

規格與說明

Product Overview

Your LAN or high speed traffic may exceed  1.5 Mbps, yet not justify the cost of an STM-1/OC-3 pipe. IME-800 inverse multiplexer bridges the gap between T1 and Ethernet, cost-effectively transports your LAN or high speed data traffic across multiple, stable, and robust TDM links.

Cost-Effective LAN Extension (LAN over WAN)

As broadband communications increases, so does the need for higher WAN bandwidth (above T1 data rate). However, STM-1/OC-3 pipes are still very expensive. Moreover, they are not always readily available, and are often overkill for the traffic capacity.

IME-800 transfers Ethernet packets transparently, enabling service providers to use their next generation equipment in TDM environment. The pure Ethernet payload carried by IME-800 eliminates the need to invest in conversion equipment between Ethernet/IP and TDM, e.g. Router and CSU/DSU.

Specification

Line Interface

Port: up to 4 x T1  (ANSI T.102) Interface: RJ-48c (100 Ohm)
Line Coding: B8ZS or AMI

Ethernet Interface (LAN)

Port: 100 Base-TX Ethernet
Interface: RJ-45

Dimensions (H x W x D)

 44 x 320 x 125 (mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                             

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% non condensing

Configuration and Management

RS-232 console port (Craft Terminal)

規格與說明

Ethernet over 1/2/4E1 Inverse Multiplexer

Bridge the Gap between E1 and Ethernet with TDM Inverse Multiplexing

Product Overview

Your LAN or high speed traffic may exceed 2 Mbps, yet not justify the cost of an STM-1/OC-3 pipe. IME-800 inverse multiplexer bridges the gap between E1 and Ethernet, cost-effectively transports your LAN or high speed data traffic across multiple, stable, and robust TDM links.

Cost-Effective LAN Extension (LAN over WAN)

As broadband communications increases, so does the need for higher WAN bandwidth (above E1 data rate). However, STM-1/OC-3 pipes are still very expensive. Moreover, they are not always readily available, and are often overkill for the traffic capacity.

IME-800 transfers Ethernet packets transparently, enabling service providers to use their next generation equipment in TDM environment. The pure Ethernet payload carried by IME-800 eliminates the need to invest in conversion equipment between Ethernet/IP and TDM, e.g. Router and CSU/DSU.

Product Overview

Your LAN or high speed traffic may exceed 2 Mbps, yet not justify the cost of an STM-1/OC-3 pipe. IME-800 inverse multiplexer bridges the gap between E1 and Ethernet, cost-effectively transports your LAN or high speed data traffic across multiple, stable, and robust TDM links.

Cost-Effective LAN Extension (LAN over WAN)

As broadband communications increases, so does the need for higher WAN bandwidth (above E1 data rate). However, STM-1/OC-3 pipes are still very expensive. Moreover, they are not always readily available, and are often overkill for the traffic capacity.

IME-800 transfers Ethernet packets transparently, enabling service providers to use their next generation equipment in TDM environment. The pure Ethernet payload carried by IME-800 eliminates the need to invest in conversion equipment between Ethernet/IP and TDM, e.g. Router and CSU/DSU

 Specification

Line Interface

Port: up to 4 x E1 (ITU-T G.703)
Interface: RJ-48c (120 Ohm)
Line Coding: HDB3

Ethernet Interface (WAN port)

Port: 100 Base-TX Ethernet
Interface: RJ-45

Dimensions (H x W x D)

 44 x 320 x 125 (mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                              

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% non condensing

Configuration and Management

RS-232 console port (Craft Terminal) 

規格與說明

ProFOM-1200 (8E1~16E1 or 8T1 ~16T1)
Next-Generation Fiber Optical Multiplexer

ProFOM-1200 is a cost-effective and good-performance product that provides 8/16  E1/T1, 2/4 DS3,  4/8 ports of 10/100BaseT card as tributary.   It deliveries various services to the customer premises over STM-1 (155Mbps)  optical network.

The ProFOM-1200 system is the transmission equipment which can provide a flexible and versatile solution to TDM and IP services and use two fiber links for 1+1 auto protection to deliver up to 155Mbps based on customer’s application.

Versatile Network Management System

ProFOM-1200 provides a functional Craft Interface and easy-to-use SNMP-based  Network Management. Performance indexes are also available for better monitoring. Easy and smooth facilities  provide powerful operation and maintenance for both remote and central sites.

Scalability in Ethernet service

The Ethernet service is scalable to fit in fields required by administrators from 2 up to 100 Mbps (increased by 2.048Mbps or 1.544Mbps) with GFP, VCAT &  Link Capacity Adjustment Scheme (LCAS) to adjust in transmission capacity with hitless traffic for user bandwidth requirement.

Specification

規格與說明

ProFOM-1600(4E1 or 4T1)
Fiber Optical Multiplexer(Single-mode or Multi-mode)

ProFOM-1600 is designed as a multi-service access platform for E1 (or T1)over Fiber applications. E1 frames can be mapped/de-mapped into/from IP packets. An adaptive clock recovery method for Ingress PDH (PSN -> TDM) clock generation is implemented to support E1 (ITU-T G.823) Jitter performance.

Cost-effective LAN Deployment
(PDH over fiber Optical)

ProFOM-1600 provides cost-effective applications of traditional circuit-switched system over fiber. With ProFOM-1600, it is easy to interconnect with the existing E1 systems over fiber that are used to carry data, voice and video.

Transparent Transmission

ProFOM-1600 can transparently transport proprietary signaling that is required to support PABX & IP-PABX features, including call conference, call forwarding and SS7. Customer can easily apply and enjoy better integration of TDM and Ethernet devices with lower network expense.

Bypass International Toll

With a pair of ProFOM-1600 and guaranteed internet bandwidth, it is sure to save cost dramatically, and to ensure the QoS of voice based on interconnections of TDM telecommunications equipment.

Specification

Line  Interface

Port: up to 4 x E1 or 4x T1  (ITU-T G.703)
Interface: RJ-48c (120 Ohm)
Line Coding: HDB3 (E1) , B8ZS(T1)

Fiber Optical  Interface

WAN Port: 1 x 100Base-FX SFP slot

Connector: SFP  LC Type

Rate: 100Mbps

Ethernet Interface

LAN port: 100 Bases-TX Ethernet
Interface: RJ-45

Dimension

H x W x D: 44 x 320 x 125(mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                             

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% none condensing

Configuration and Management

規格與說明

ProFOM-1600(2E1 or 2T1)

Fiber Optical Multiplexer(single-mode or Multi-mode)

ProFOM-1600 is designed as a multi-service access platform for E1 (or T1)over Fiber applications. E1 frames can be mapped/de-mapped into/from IP packets. An adaptive clock recovery method for Ingress PDH (PSN -> TDM) clock generation is implemented to support E1 (ITU-T G.823) Jitter performance.

Cost-effective LAN Deployment
(PDH over fiber Optical)

ProFOM-1600 provides cost-effective applications of traditional circuit-switched system over fiber. With ProFOM-1600, it is easy to interconnect with the existing E1 systems over fiber that are used to carry data, voice and video.

Transparent Transmission

ProFOM-1600 can transparently transport proprietary signaling that is required to support PABX & IP-PABX features, including call conference, call forwarding and SS7. Customer can easily apply and enjoy better integration of TDM and Ethernet devices with lower network expense.

Bypass International Toll

With a pair of ProFOM-1600 and guaranteed internet bandwidth, it is sure to save cost dramatically, and to ensure the QoS of voice based on interconnections of TDM telecommunications equipment.

Specification

Line  Interface

Port: up to 2x E1 or 2x T1 (ITU-T G.703)
Interface: RJ-48c (120 Ohm)
Line Coding: HDB3(E1) or B8ZS(T1)

Fiber Optical  Interface

WAN Port: 1 x 100Base-FX SFP slot

Connector: SFP  LC Type

Rate: 100Mbps

Ethernet Interface

LAN port: 100 Bases-TX Ethernet
Interface: RJ-45

Dimension

H x W x D: 44 x 320 x 125(mm)

Main Power Supply

AC: 85 ~ 264V @ 47 ~ 63Hz
(Optional) DC: -72V ~ -36V                             

Environment Condition

Ambient temperature: 0℃ ~ 50℃
Storage temperature: 0℃~ 85℃
Relative humidity: 5 ~ 95% none condensing

Configuration and Management

RS-232 console port (Craft Terminal) or Telnet

規格與說明

OTN-100G

OTN-100G (Optical Transport Network) is a Wire Optical Transport Devices.   Not only stanard  product cargo with 100G optical line port & 10x10Gbps optical Etherent client ports,  but also extendable as chassis-type with “pluggable 100G Transponder/Muxponder special ports creation. Let user interface  meet to the customized requirement to include various 100G interface conversion. For management part, engineering CLI (RS-232) & simple Etherent(RJ-45) port are provided & system can be configured as Web browser/SNMP/MIB w/ SDN-controlling capability.  Network application topology would  be a simple  100G ports “converter”, “point-to-point link ”, “dual path protection”, or “flexible  ring” various network application design

 With an 100G uplink to all optical network field, this device can provide “5G/4G fronthaul/midhaul”, “GPON backhaul”, “GigaAccess backhaul” services and “bridging various cloud Datacenter/Edge optical ports with the required 100G/10G traffic link extension. This standard box is  “100G OTN/10x10G Ethernet” & can be flexible for other client interface  by proper effort involved.  Due to more rapid growthing  at  “5G mobile Network/B5G-6G-Satellite”, “all optical Fixed Network” & “Cloud Data Center” migrating trend, network equipment need 100Gbps-base high bandwidth to support. This  100G-OTN is a highly compacted box for mobile network/Video/AR/VR/AI application by proper transponder/muxponder service traffic into OTN(OTU4) frame structure.  Let network system can more flexibly meet new service applications by 100G-base huge bandwidth deployment

l  Smoothly merge the TDM & Ethernet/IP traffic ports  into All-Photonics Network  world : To meet IOWN (Innovative Optical & Wirelesss Network) service developing requirement

l  Scalability in Ethernet service : The Ethernet service is scalable to fit sites request by design-in 100Gbps and client-side can be from one 10Gbps to multiple 10Gbps as easier bandwidth expansion.

l  Versatile Network Management System : To provide a Craft Interface and easy-to-use Network Mangemant (SNMP-base), there is also MIB sets for customized facilities to get integratable O&M &  to be  viewed at  both remote and central side.

Specification

規格與說明

2 Slot IPPBX

• 尺 寸 (cm) ：4.5(H) x 44(W) x 30(D)
  ●CPU：ATOM D525
  ●記 憶 體：DDRII 4GB
  ●網 路 端 口：10/100/1000 LAN x2,
  ●硬 碟 容 量：500G 
  ●USB 2.0 Port：2 (Front)
  ●FXO/S：4 Port
  ●電 源：80W External 110VAC /220VAC Adapter
  ●工作溫度：0 - 40°C
  ●工作溼度：8% to 90% (non-condensing)

語音規格
●符合SIP RFC 3261 / H-323 規範(ITU-T) 通信協定
●語音壓縮規格: G.711,G.722,G.723,G.726,G.729,GSM,Slin,Lpc10,Speex
自動總機
●Web 介面自動總機語音流程編輯
●特定時間宣告語
●假日工作時間設定
●支援多國語言
交換機ISDN鍵結
●Toshiba,NEC,Alcatel,Avaya,phillips...等
語音郵箱
●支援多國語言
●SIP留言指示
●電子郵件通知
●可由Web存取語音留言
●可由電話聽取語音留言
會議功能
●隨取建立會議室
●個人虛擬會議室
●會議事件提示音
●單一會議室最多可容納32名成員
●可由網路電話登入
加強功能
●多應用IVR(語音互動系統) 資料庫
●可支援 SIP/H323/MGCP/G-Talk/OCS/Skype 鍵結
精選電話功能
●通話轉接 Transfer
●來電轉送 Forward
●來電轉送通知 Forwarded Notice
●撥號限制 Call Screening
●去電顯號設定 Caller ID Privacy
●來電等候 Call Waiting
●通話保留 Call Hold
●來電代接 Call Pickup (Global, Group)
●指定代接 Specified Call Pickup
●電話跟隨 Follow Me
●勿打擾 Do Not Disturb
●去電顯示替換 ANI Replacement
●回撥 Call Return
●隱藏或顯示主叫號碼 Hide /Show ANI Selection
●通話駐留與取回 Call Park/Retrieve
●分機註冊 Extension mobility
●忙線自動回覆 busy call back

規格與說明

xDSL/GPON/CWDM Series